MonoCoat 1K Direct to Rust - Silver

Product Description

MonoCoat 1K Direct to Rust Urethane

Silver

  

A moisture-curing coating is a type of coating that cures due to the presence of moisture in the atmosphere. This coating forms a protective coating film by reacting chemically with the moisture in the air. It is designed to paint directly over sound rusted metal surfaces to stop rust permanently. Waterproof! Perfect for the marine environment. Impervious to chemicals, salt, and other corrosive contaminants and is able to be painted over rust.

This is nothing like POR15, this Mono cure technology supersedes any kind of POR15 products on the market.

Reduction is not needed unless you plan to spray Monocoat.

Monocoat is a high-performance, moisture-cured coating that encapsulates and stops rust from spreading. It designed to be top coated with almost any paint. In some areas you *could leave it as a Topcoat, but chalking can occur in direct sunlight.

Monocoat can be applied over bare metal or surface rusted areas. Brush or spray applied. It is ideal for any type of rusted metal surface and can handle temperatures up to 350 degrees. 

Can be used outdoors at temperatures as low as 40 degrees. Assuring excellent adhesion and impact resistance along with industry leading corrosion protection and encapsulating properties.

Mono component aluminum pigmented coating

67% solids by weight

Approximate coverage: 96 SQ FT per quart for one coat

1 coat assures maximum protection

Brush, roller or spray applied

Paint Gun: HVLP gravity or siphon with a 1.4 minimum needle/nozzle

Re-coat able after 4 hrs.- if top coating after 48 hrs., scuff surface with 320 grit paper

2 hrs and tack free

Easy to apply

Topcoat able with virtually any high-quality coating

Maximum service temp of 350 Degrees 

TDS Sheets

Q&A

Q:  Can I use a Brush or Roller to apply Monocoat?

A: Yes

Q:  Can I use Ospho or rust neutralizers??

A: NO!! Do not use any form of rust converters, metal conditioners, rust neutralizers. It is not needed with Monocoat and will react or not stick and fail.

Q: How much Monocoat Reducer do i add in the can to "preserve" the Monocoat left in my can?

A: Add a half inch barrier. Eyeing the measurement will be ok

Q: Can I just use the HR Reducers??

A: No! These are not the same, at all!! Even if you are in a pinch, this wont work.

Q: How much Monocoat reducer do i add to spray?

A: You can add up to 25% Monocoat reducer, tip size should be 1.8 @ 25% reduction.

Q: Monocoat vs Chassis Black. Which one should I use?

A:  Chassis is a alkyd and Monocoat is moisture cured. Very different products. Which one depends on your job

Use Monocoat for small areas, hard to reach areas and under carriages.

Chassis Black is really designed for large areas.

Q: Is Monocoat is a semi or gloss??

Monocoat is a semi gloss, but it will flatten in sun light. It will also chalk in sunlight

Q: Does Monocoat has gloss retention?

A: No, it will chalk in the sunlight. Use Chassis Black for sunlight pieces.

Q: Can Monocoat be applied over rust?

A: Hell yes! Monocoat is awesome for this type of need. Monocoat is a rust preventative and anti corrosion restoration coating.

Q: How do I apply over rust??

A:

Get as much rust off as you can by mechanical abrasion by sandblasting or sanding with 40 - 600 grit

Clean the rust as throughout as possible. Use our HR397 Wax & Grease remover

Do not use any form of rust converters, metal conditioners, rust neutralizers. it is not needed with Monocoat and will react or not stick and fail.

Q:  Can I apply Monocoat, and then put a sound insulator over it like dynamat of kill mat or similar without top coating it?

A: Yes, absolutely.

Q: How long should I wait after applying Monocoat to install the Dynamat?

A: 24 Hours

YouTube Videos